Equipment
How to create your own custom-stamped wedges
Like so many other readers here on GolfWRX, I eagerly look forward to PGA Tour WITB photos each week. One of the most interesting aspects of Tour bags for me (and especially at the Waste Management Open) has always been the custom-stamped wedges and irons, like Pat Perez wedge pictured above. Custom stamping is no longer just for the Tour, however.
Cleveland, Mizuno and Vokey offer different options as well as initial stamping on their wedges and this year Nike is offering it on its irons. But, like many other at-home projects, it’s just so much more satisfying to do it yourself. Let these pictures be a guide to getting started. It’s easier (and could be cheaper) than you think!
Materials
- Stamping kit: Harbor Freight $9.99, Amazon.com $15 to $100.
- Hammer/Mallet: I have a 4-pound mallet and found that to be the most effective.
- Tape: Double-sided and masking.
- Paint (Optional).
Setup
The goal here is to firmly secure the club face to a hard surface. If you have access to a vise, you are in business as most vises have an anvil. If not, just make sure that the clean club face is firmly secured with double-sided tape. You may need someone to hold the club head securely in place while you swing the mallet, which is not as dangerous as it sounds.
Stamping
Identify the area you want to stamp and cover it with masking tape. This serves three purposes: you are able to draw reference lines with a straight edge to make your stamping neat, the imprint shows better on the tape so you can re-align your stamp for successive strikes and the tape absorbs some of the blow, making it less likely that the stamp will “bounce” and create a second impression on the wedge.
Take note of how far apart you are spacing consecutive letters as most first-time projects end up looking a bit like this: “G O L FW R X”
Let’s face it: some guys are better with a hammer than others. If you can make a confident swing at the stamp and create a deep imprint with just one swing then good for you! If not, it’s OK to take multiple swings. In fact, you’ll see Scotty Cameron doing just that if you watch this video from his website. According to Cameron, deeper strikes look “more finished … thin looks dainty and weak.” From my own experience, I have learned it is best to oscillate the stamping pin so that each successive strike drives the stamp from different angles to ensure that the stamping is symmetrical and deep.
Now bask in the glory of your very own “Tour” golf club! Obviously, this will take a little bit of practice. In the spirit of “measure twice, cut once,” you should probably try making a few practice stamps on an old club first. Keep in mind that forged clubs will be much more receptive to stamping than cast ones. Even with the cheaper Harbor Freight stamping kit, I still have not come across a wedge that is “unstampable” though.
Paint is optional and a great way to further customize your clubs. You can find many posts in the forums detailing different user methods. If nothing else, it most certainly brings a smile to my face when I look down in my bag to grab my DIY custom-stamped golf clubs.
This week, we have our Tour Photographer, Greg Moore, on the ground at the OccuNet Classic at Tascosa Golf Club in Amarillo, Texas, for the 14th event of the 2026 Korn Ferry Tour season. With that, we see some great things in the Lead Tape Report as we roll into Amarillo.
Joel Thelen
Monday Qualifier, Joel Thelen is in the field this week. He has played on the Korn Ferry Tour for a full season in 2023, and he is back in action this week. A couple of clubs caught my eye this week in his bag.
First off: His trusted Titleist 816 H2 hybrid. This club came out in October of 2015, and it still remains strong in the bag. Also, take a look at this Odyssey White Hot OG 7, putting a capital S in the 7S model. This custom neck has some impressive lean for an arm-lock-style putter. The bottom of the putter is covered in tape for optimal weighting.
Mitchell Meissner
Taking a look at Mitchell Meissner’s bag this week, we have some great lead tape coverage. Top to bottom working from fairway metals, irons, and wedges. We can see on the short irons and wedges that there is tape at the base of the grip, adding a little counterbalance. Along with that, some tape on the short irons and wedges as well. Moving to his putter, he rolls the Odyssey 7 Bird putter. Meissner putts left-handed and strikes the ball right-handed.
Bud Cauley had >14 clubs in his bag when photographed prior to the Memorial Tournament.
Driver: Titleist GTS2 (8 degrees)
Shaft: Fujikura Ventus Black 6 X
3-wood: Titleist GTS3 (15 degrees, B1 SureFit setting)
Shaft: Mitsubishi Chemical Tensei 1K Pro Red 70 TX
7-wood: Titleist GTS3 (21 degrees, D1 SureFit setting)
Shaft: Mitsubishi Chemical Tensei 1K Pro Red 80 TX
Irons: Titleist U505 (3), Titleist 620 MB (4-9)
Shafts: Fujikura Ventus Black HB 8 X, True Temper Dynamic Gold Tour Issue
Wedges: Titleist Vokey Design SM11 (48-10F, 52-12F, 56-14F), WedgeWorks (60-K*)
Shafts: True Temper Dynamic Gold Tour Issue S400
Putters: Scotty Cameron Tour Prototype, Scotty Cameron GOLO 6.3 Prototype
Grips: Golf Pride Tour Velvet Align
Ball: Titleist Pro V1
In our forums, one user has offered up a prompt for the true sickos, inviting fellow forum members to share every set of irons they’ve ever owned. As to be expected, this is a lengthy forum topic.
@Lamosteve began:
Can you name every set of irons you’ve owned? Here’s mine
Spalding Dots
Spalding Eclipse
Ram Lazer FX
Lynx Parallax
Mizuno EZ Comp
Ben Hogans
Cleveland CG Red
Taylor Made R9s
PING i20
PING iE1
Taylor Made M6
Our members in the forum have been offering up their own collections. Here are a few posts from the thread, but make sure to check out the entire discussion and have your say at the link below.
- macedan: “Started with a hand-me-down Golden Bear set from my brother when I was in high school, never really played more than once a year or got into the game until about summer of 2017. First purchased a set of Cleveland CG4’s (I actually really miss this set sometimes, soft & not terribly large for a GI iron), moved into Nike Vapor Fly’s by the end of the year. Those lasted until spring of 18 when I decided I wanted new, so I traded them in for TM Rbladez. Honestly, although I liked the Rbladez, poor decision on my part, I think this was really about the only time so far that after a week or two I was kicking myself for not staying with what I had. Rbladez stayed with me until late last summer when I switched to P790’s and (knock on wood) I am hoping this will be my longest lasting set.”
- JimmyC59: “MacGregor Jack Nicklaus Triple Crown. Palmer The Standard. Still play these.”
- jgrzask: “Tommy Armour 845u
Mizuno MP-32
Mizuno MP-33 (2 sets)
Bridgestone J33cb – still own
Srixon i-302 (2 sets) – still own
Tourstage X-Blades – still own
Mizuno Hot Metal – still own
Nike Forged Blades – still own
Titleist 714 AP1 – still own
Cobra Forged SS – still own”
Justin Rose WITB 2026 (April): Full WITB breakdown with new McLaren irons
What’s the story behind Webb Simpson’s custom-stamped irons?
Memorial Tournament Tour Report: Rory McIlroy, Cameron Young switch up drivers, and more
Cadillac Championship Tour Report: Spieth’s sizable changes, McLaren Golf launches, and more
Russell Henley’s winning WITB: 2026 Charles Schwab Challenge
Kristoffer Reitan’s winning WITB: 2026 Truist Championship
Best irons 2026: Best irons overall, most forgiving irons, and more
J.T. Poston’s winning WITB: 2026 Memorial Tournament
Aaron Rai’s winning WITB: 2026 PGA Championship
Cameron Young’s winning WITB: 2026 Cadillac Championship
Bud Cauley WITB 2026 (June)
Bud Cauley had >14 clubs in his bag when photographed prior to the Memorial Tournament. Driver: Titleist GTS2 (8 degrees) Shaft: Fujikura...
Hannah Green WITB 2026 (June)
Driver: Titleist GTS3 (10 degrees, D4 SureFit setting) Shaft: Mitsubishi Chemical Diamana RB 53 S 3-wood: Titleist GT3 (15 degrees,...
Asterisk Talley WITB 2026 (June)
Driver: TaylorMade Qi4D (9 degrees) Shaft: Fujikura Ventus Blue 6 S 3-wood: TaylorMade Qi4D (16.5 degrees) Shaft: Fujikura Ventus Blue...
Brianna Do WITB 2026 (June)
Driver: Callaway Quantum Triple Diamond (9 degrees) Shaft: KBS PGW 3-wood: Callaway Elyte Titanium (15 degrees) Shaft: KBS PGW 5-wood:...
-
Equipment6 days agoMemorial Tournament Tour Report: Rory McIlroy, Cameron Young switch up drivers, and more
-
News2 weeks agoRussell Henley’s winning WITB: 2026 Charles Schwab Challenge
-
Equipment3 days agoBest irons 2026: Best irons overall, most forgiving irons, and more
-
Whats in the Bag4 days agoJ.T. Poston’s winning WITB: 2026 Memorial Tournament
-
Equipment1 week agoDetails on Jason Day’s latest prototype Avoda iron setup
-
Equipment3 weeks agoCJ Cup Byron Nelson Tour Report: Koepka and Kim’s newest putters finally get hot
-
News2 weeks agoCharles Schwab Challenge Tour Report: MacIntyre, Åberg and Spaun all switch putters, TaylorMade launches new Spider
-
Equipment2 weeks agoDetails on J.J. Spaun’s surprise putter switch
Gary
Jun 16, 2015 at 2:14 pm
Instead of using mallet would a impact driver work work?
Kevin
Dec 17, 2014 at 5:18 pm
I used to punch stamp my clubs but the results were not as good as I wanted. So after searching on the internet I found http://www.personaltouchsports.com These guys did amazing work. After going through them I would never punch stamp again!
Corey
Nov 8, 2014 at 1:29 pm
Where can I get that solid dot stamp and what’s the best way to fill in the stamps with paint
nik dallos
Feb 7, 2014 at 10:41 pm
I am embarrassed someone even had to give this tutorial. Next tip, how to tie laces on your shoes. And how to put new grips on your clubs! Man im a negative nantz. Feel free to swear at me and put me down.
melrosegod
Feb 7, 2014 at 4:31 pm
I have stamped a few wedges and I like the “not so clean look”. That said, layer 4 or 5 strips of masking tape to develop an indentation when you stamp. It will help you keep your die in place for multiple hits.
Tony
Feb 7, 2014 at 3:52 pm
Anyone tried this on Ping wedges? Specifically the Tour S’s.
Thx
Jon Deerman
Feb 6, 2014 at 12:43 pm
As a metal worker with stamping experience, I would suggest to practice your technique on an old club or scrap piece of metal. Many first timers (including myself at the beginning) will not place the stamp correctly, causing uneven stamps or even damage to the material itself. (This means you must take a grinder and remove material to take the “bad” stamp away, which could change the feel of your club) As all things with golf it comes with practice, so if you keep at it success will come. Just remember… don’t make your first stamp an attempt to do it on those new Vokey’s or Fourteens.
Eric Johnson
Feb 6, 2014 at 1:05 pm
Jon – good reminder. It was my experience that the spacing of the pins was difficult at first (instinctively I placed the stamps too far apart) and that the depth of the stamp was not uniform. It was when I struck the stamp from several different angles that I saw the best results. Any other suggestions from your experience?
Jon Deerman
Feb 6, 2014 at 2:37 pm
Don’t be afraid to swing the hammer harder then you think, it is steel and most of the time this is a problem leading to a dreaded double hit. (Same stamp, same location but slightly off) On ease of use, there are metal stamp holders which allow a number of pins(They very from size to price, ebay being the best source), will allow you to stamp it in one swing. You may have to go over a few of the stamps but it will be quicker. If there is a missed hit, rock the pin until it settles in the previous stamp, and rock it slightly to the unmarked area hitting it with the hammer. On spacing it is good to have a lined up one after the other method. The gaps between the pins are usually what size it is (1/8″ Stamp should have 1/8″ between letters). A cost effective approach is to put a light coat of removable metal paint marker (around $5) on the bottom of your pins, placing them where you would like to see them on your clubs. This should create a template for better spacing.
zack
Feb 5, 2014 at 6:03 pm
I have cleveland cg14 wedges and find them to be un-stampable. I was wondering if anybody has stamped a cg14 wedge before and can give me any tips
Eric Johnson
Feb 5, 2014 at 7:44 pm
Zack –
CG14 are the same wedges I use and have had success stamping them all (I have 5!). I would guess that your wedges are not set firmly enough in place or your hammer/mallet is not heavy enough.
Mark
Feb 5, 2014 at 4:34 pm
What size stamp should I buy? 1/8″ ?
Eric Johnson
Feb 5, 2014 at 5:58 pm
Yes 1/8″ is the size you normally see
John Moriarty
Feb 5, 2014 at 3:55 pm
You do not ruin the finish when you stamp into it. Also instead of masking tape us double sided tape where you are going to stamp. You can press the stamp in by hand first and it leaves a mark of the letter. It allows you to plan out a bit better. Also when you hammer away the stamp won’t slip since it’s held down by the tape.
Roberat Upton
Feb 5, 2014 at 2:52 pm
Frankly, that cheap square font on those punches looks amateurish, cheap and nasty to me ? Why would you want to de-value a relatively expensive club like that ?
Jack
Feb 6, 2014 at 3:09 am
Roberat, tons of golf pros have it done, so maybe we just want to be like them? I’ve not done it personally since it does affect the resale value.
Nate
Feb 7, 2014 at 4:16 pm
When I did mine I purchased a Comic Sans set of stamps instead of the block font (believe its Courier). There are also some design stamps people might find interesting, like a bird or clover. My vokeys get a clover for each chip-in or hole-out.
Anthony H Melia
Dec 27, 2020 at 10:22 am
Great idea, like a college football helmet! I’m stealing this.
Monster
Mar 30, 2014 at 8:59 am
Roberat, It is meant to look that way. Its personal, A wedge is to be used until the grooves are gone. They are not for real sale. Next time you’re working on the game, Put your driver down and Go practice some wedges.
Chris
Feb 5, 2014 at 2:50 pm
I always love the phrase “it is not as dangerous as you would think”
Kevin Hefner
Feb 5, 2014 at 2:33 pm
What happens to the plating on the wedge, if it is chrome plated or a black wedge?
Eric Johnson
Feb 5, 2014 at 3:03 pm
Kevin – I have had no wear issues stamping chrome plated and raw clubs. I personally have not stamped any darker finished clubs but cannot foresee any danger to the club’s integrity. If you’re worried about rust then I’d be sure to fill in your stamps with paint. Good luck with your “wedged” haha